Serial Lcd Display Pinout
The 2.8' TFT display on this breakout supports many different modes - so many that the display itself has 50 pins. However, we think most people really only use 2 different modes, either 'SPI' mode or 8-bit mode (which includes both 6800 and 8080). Each 'side' of the display has all the pins required for that mode.
You can switch between modes, by rewiring the display, but it cannot be used in two modes at the same time! All logic pins, both 8-bit and SPI sides, are 3-5V logic level compatible, the 74LVX245 chips on the back perform fast level shifting so you can use either kind of logic levels.
If there's data output, the levels are at at 3.3V. GND - this is the power and signal ground pin. 3-5V / Vin - this is the power pin, connect to 3-5VDC - it has reverse polarity protection but try to wire it right!. 3.3Vout - this is the 3.3V output from the onboard regulator. CLK - this is the SPI clock input pin.
Pinout For Serial Cable
MISO - this is the SPI Master In Slave Out pin, its used for the SD card mostly, and for debugging the TFT display. It isn't necessary for using the TFT display which is write-only. MOSI - this is the SPI Master Out Slave In pin, it is used to send data from the microcontroller to the SD card and/or TFT. CS - this is the TFT SPI chip select pin.
NetMedia 2x16 Serial LCD Display Module V1.2 • RS232 compatible serial interface. Pinout Power and communications connections are made via header J5.
D/C - this is the TFT SPI data or command selector pin. RST - this is the TFT reset pin. There's auto-reset circuitry on the breakout so this pin is not required but it can be helpful sometimes to reset the TFT if your setup is not always resetting cleanly. Connect to ground to reset the TFT. Lite - this is the PWM input for the backlight control. It is by default pulled high (backlight on) you can PWM at any frequency or pull down to turn the backlight off.
IM3 IM2 IM1 IM0 - these are interface control set pins. In general these breakouts aren't used, and instead the onboard jumpers are used to fix the interface to SPI or 8-bit. However, we break these out for advanced use and also for our test procedures.
Card CS / CCS - this is the SD card chip select, used if you want to read from the SD card. Card Detect / CD - this is the SD card detect pin, it floats when a card is inserted, and tied to ground when the card is not inserted. We don't use this in our code but you can use this as a switch to detect if an SD card is in place without trying to electrically query it. Don't forget to use a pullup on this pin if so! Resistive touch pins. Y+ X+ Y- X- these are the 4 resistive touch screen pads, which can be read with analog pins to determine touch points.
They are completely separated from the TFT electrically (the overlay is glued on top) Capacitive touch pins. SDA - this is the I2C data pin for the captouch chip, there's level shifting on this pin so you can use 3-5V logic. There's also a 10K pullup.
SDA - this is the I2C clock pin for the captouch chip, there's level shifting on this pin so you can use 3-5V logic. There's also a 10K pullup. IRQ - this is the captouch interrupt pin. When a touch is detected, this pin goes low. GND - this is the power and signal ground pin. 3-5V (Vin)- this is the power pin, connect to 3-5VDC - it has reverse polarity protection but try to wire it right!. CS - this is the TFT 8-bit chip select pin (it is also tied to the SPI mode CS pin).
Character Lcd Pinout
C/D - this is the TFT 8-bit data or command selector pin. It is not the same as the SPI D/C pin! Instead, it's the same as the SPI CLK pin. WR - this is the TFT 8-bit write strobe pin.
It is also connected to the SPI D/C pin. RD - this is the TFT 8-bit read strobe pin.
Hd44780 Lcd Pinout
You may not need this pin if you don't want to read data from the display. RST - this is the TFT reset pin. There's auto-reset circuitry on the breakout so this pin is not required but it can be helpful sometimes to reset the TFT if your setup is not always resetting cleanly. Connect to ground to reset the TFT. Backkite - this is the PWM input for the backlight control.
It is by default pulled high (backlight on) you can PWM at any frequency or pull down to turn the backlight off. D0 thru D8 - these are the 8 bits of parallel data sent to the TFT in 8-bit mode. D0 is the least-significant-bit and D8 is the MSB. You have been successfully subscribed to the Notification List for this product and will therefore receive an e-mail from us when it is back in stock! For security reasons, an e-mail has been sent to you acknowledging your subscription. Please remember that this subscription will not result in you receiving any e-mail from us about anything other than the restocking of this item.
If, for any reason, you would like to unsubscribe from the Notification List for this product you will find details of how to do so in the e-mail that has just been sent to you!
. Specials $129.99 USD $101.39 USD. The HTT series offers full colour TFT displays with a simple HDMI and USB plug and play interface. Designed with industrial applications in mind, the HTT is perfect for panel mounted applications and HMI interfaces. Features: 5.0' (800x480) - Non-Touch Plug and Play &nb. $71.22 USD - $74.85 USD The HTT series offers full colour TFT displays with a simple HDMI and USB plug and play interface. Designed with industrial applications in mind, the HTT is perfect for panel mounted applications and HMI interfaces.
Features: 7.0' (800x480) - Resistive Touch Plug and Play &nb. $86.59 USD - $89.82 USD The HTT series offers full colour TFT displays with a simple HDMI and USB plug and play interface. Designed with industrial applications in mind, the HTT is perfect for panel mounted applications and HMI interfaces. Features: 5.0' (800x480) - Capacitive Touch Plug and Play &n. $86.22 USD - $89.85 USD The USB to SPI Development Kit for Matrix Orbital EVE Display Modules Includes: USB to SPI Bridge Module Mini-B USB Cable (EXTMUSB3FT) 20pin Flat Flexible Cable (FFC-20P) Four (4) Bumpons The Matrix Orbital USB to SPI Bridge utilizes FTDI’s FT232H IC, allowing users to communicate to their SPI device.
$18.30 USD - $19.87 USD Matrix Orbital EVE2 TFT's utilize FTDI's second generation Embedded Video Engine to control, render, manage and display complex graphics. With built in graphics operations, sound synthesizer, digital filter and support for multiple widgets you can create your own stunning screens and interfaces with the EVE Screen Designer software.
$73.94 USD - $80.31 USD Matrix Orbital EVE2 TFT's utilize FTDI's second generation Embedded Video Engine to control, render, manage and display complex graphics. With built in graphics operations, sound synthesizer, digital filter and support for multiple widgets you can create your own stunning screens and interfaces with the EVE Screen Designer software. $69.03 USD - $74.48 USD Specials For February $129.99 USD $101.39 USD $149.99 USD $116.99 USD $129.99 USD $101.39 USD Your Account Login Problems? Your Email Address Your Password Shopping Cart 0 items Best Sellers 01. Information Copyright © 2018.